compression loading造句
例句与造句
- Advanced technical ceramics - mechanical properties of ceramic composites at high temperature under inert atmosphere - determination of shear strength by compression loading of notched specimens
高级工业陶瓷.惰性气体环境中高温情况下陶瓷成分的机械特性.通过有凹槽试样的压力荷载测定剪切强度 - Advanced technical ceramics - mechanical properties of ceramic composites at room temperature - part 4 : determination of interlaminar shear strength by compression loading of notched test specimens
先进工艺陶瓷.室温下陶瓷复合材料的机械性能.第4部分:用切口试样的压缩负荷法测定层间的剪切强度 - Advanced technical ceramics - mechanical properties of ceramic composites at high temperature under inert atmosphere - determination of shear strength by compression loading of notched specimens
高级工业陶瓷.惰性气体环境中高温情况下陶瓷复合材料的机械特性.通过有凹槽试样的压力荷载测定剪切强度 - The main structure stress of the car body is particularly analyzed . it is analyzed and calculated under vertical load case , lengthwise stretch load case , lengthwise compression load case , air pressure power load case , operating load case . result shows : the structure distortion harmonize , strength - weakness positions represent local stress focus
通过对垂向载荷工况、纵向拉伸载荷工况、纵向压缩载荷工况、气动载荷工况和运用状态垂向载荷工况的分析计算，结果表明：该车钢结构变形协调，强度薄弱部位主要表现为局部应力集中。 - The main research is below : ( 1 ) the influence to intensity and rigid with corner angle ( 60 , 75 and 90 degree ) of crack and the board axes ( 2 ) do a fem stress / strain and crack growth simulation analysis when the corner angle of crack and the board axes is 60 degree ( 3 ) do a intensity resume analysis for the structure which is repaired with a titanium patch in a mechanical way when the corner angle of crack and the board axes is 60 degree through simulation analysis for three failure criterion , we have : ( 1 ) in 60 , damage extend quickly with damage analysis in hashin criterion ; it is slower for analysis in maximum stress or hashin - rotem criterion . ( 2 ) in special term ( physical condition incision , shape or maximum load ) the compression strength of the stiffened plate will decline 45 % ~ 50 % under compression loads
通过采用三个不同损伤判据的数值仿真模拟，得到如下结论： ( 1 )在60时，用hashin判据进行的损伤分析，损伤扩展较快；最大应力及hashin - rotem判据进行的损伤分析，损伤扩展基本相当，且较慢； ( 2 )在所给加筋板的物理条件、切口大小及形状、最大载荷等一定的条件下，该加筋板在压缩载荷作用下，其压缩强度下降了45 50 ； ( 3 )在本文提及到的机械连接修理方法以及载荷条件下，修理后的结构强度恢复能够满足战时要求。 - It's difficult to find compression loading in a sentence. 用compression loading造句挺难的
- Merely the fatigue strength in uniaxial tension or compression under constant - amplitude cyclic loading is given in the existing design code . the design result by using the fatigue strength in the code is apt to conservative under variable - amplitude or triaxial cyclic compression loadings , but sometimes apt to dangerous in uniaxial or triaxial tension - compression fatigue loadings
现行规范中，仅有混凝土单轴、等幅波动拉伸和抗压强度指标，采用这些指标进行设计，会导致设计结果有时偏于保守，如变幅及多轴压疲劳；而有时又偏于危险，如单轴及多轴波动拉-压疲劳。 - In this dissertation , the effect of texture , heat - treatment , and hydrogen on the lcf behavior of zircaloy - 4 and the cyclic deformation behavior for zircaloy - 4 , n18 alloy and n36 alloy have been investigated systematically using fully - reversed tension - compression loading under strain control ( r = min / max = - 1 ) , while the evolvement of the friction and back stresses versus the number of repeated working cycles and the plastic strain amplitude has been studied , and the thorough discussion combined with the analysis result of fatigue sub - structure , friction and back stresses , and fatigue fracture has been given to the mechanism underlying the lcf behavior of alloys
本文采用对称拉压循环变形方法( r _ = _ ( min ) _ ( max ) = - 1 ) ，系统研究了织构、热处理状态、氢对zr - 4合金低周疲劳性能的影响， zr - 4合金、 n18合金和n36合金的循环变形行为，并研究了摩擦应力、背应力随循环周次、塑性应变幅的变化规律。结合疲劳亚结构和疲劳断口的分析结果，深入探讨了影响合金低周疲劳行为的作用机制。 - Each unit anchor has its own individual tendon , its own unit fixed length of borehole , and is loaded with its own unit stressing jack which ensures that the load in all unit anchors is always identical . the total working load of the anchor is beard by each fixed anchor length of all units in staggered depth in the borehole and by means of respective bearing bodies , the tension loads applied to the plastic coated strands are changed into the compression loads on the grout of each fixed anchor length , then the total working load can be divided into several smaller loads and transmitted to the rock mass and soil in different locations in dispersed compression
压力分散型锚索是在一个钻孔中安装若干个锚索单元，每个单元都有自己的杆体和锚固段，在张拉时分别承受相同的工作荷载；锚索总的锚固力由分散布置于钻孔不同深度处的这些单元锚索的锚固段来共同承担，并利用各单元的承载体将无粘结锚索的拉力转化为对锚固段注浆体的压力，从而将锚索总的锚固力以压力形式分散作用于不同深度的岩土体上。
更多例句： 上一页